Diagnose check engine light and give estimate for repair. Diagnostic covers only codes present when vehicle is first presented. Because the check engine light monitors every system in the vehicle there are hundreds of different reasons the check engine light can be illuminated. If on returning the check engine light is illuminated and the computer is storing a different code, unrelated to any system diagnosed or repaired within the past year or 12000 miles, a distinct diagnostic fee will be charged again. TECHNICIAN NOTE Code P0303 misfire cylinder 3. Compression tested at 150 lbs on cylinder 3, misfire is not mechanical, found vehicle has BOSCH spark plugs and do not meet OEM standard per Nissan. Also found code P1273 02 sensor 1 lean condition. Checked for intake leaks and did not find any at this time, exhaust also is ok, found O2 sensor 1 bank 1 intermittently drops signa. RECOMMENDATION Ignition coils, OEM spark plugs, fuel induction service, and O2 sensor 1
CONTROL ARM – Remove & Replace – Lower,Both – [DOES NOT include alignment.]
Road test vehicle. Check all suspension and steering parts for wear. Check tire pressure and condition. Check riding height. Check alignment of all four wheels. CHECK AND SET TOE ANGLE, CHECK CAMBER AND CASTER. ADJUSTING CAMBER OR CASTER IS ADDITIONAL LABOR AND POSSIBLY PARTS.
JAKE L. gave our service a 5 star review on 1/14/2022
BG COOLANT SYSTEM TRANSFUSION SERVICE (BG PART #'S 540 & 546) COOLING SYSTEM CLEANER REMOVES TOUGH ORGANIC DEPOSITS THAT RESULT FROM OIL FOULING, GREASE AND GLYCOL OXIDATION RESIDUES. BG UNIVERSAL SUPER COOL ADDITIVE ADDS PROTECTION FOR ALL METALS, HAS CORROSION INHIBITORS AND ANTI FOAM AGENTS.
Lubricate and check chassis. Change oil and oil filter. Check air filter and breather filter. Check all fluid levels and tire pressures. Perform 40 point courtesy inspection. If applicable.
RADIATOR HOSE – Remove & Replace – 2.0L Eng Both
LUCIANO M. gave our service a 5 star review on 5/22/2020
Lubricate and check chassis. Change oil and oil filter. Check air filter and breather filter. Check all fluid levels and tire pressures. Perform 40 point courtesy inspection. If applicable.
ROAD TEST VEHICLE. INSTALL ALIGNMENT EQUIPMENT. CHECK CASTER, CAMBER AND TOE SETTINGS. ADVISE OF ANY NEEDED ADJUSTMENTS TO CASTER OR CAMBER. IF CASTER AND/OR CAMBER ARE NOT WITHIN MANUFACTURER'S SPECIFICATIONS, PREPARE ESTIMATE TO INSTALL CORRECT ADJUSTMENT DEVICES. REMOVE ALIGNMENT EQUIPMENT. ROAD TEST.
HUGO M. gave our service a 5 star review on 2/15/2020
ALTERNATOR DRIVE BELT – Remove & Replace – All Applicable Models
ENGINE DAMPER/TORQUE MOUNT – Remove & Replace – All Applicable Models
Lubricate and check chassis. Change oil and oil filter. Check air filter and breather filter. Check all fluid levels and tire pressures. Perform 40 point courtesy inspection. If applicable.
CABIN AIR FILTER – Remove & Replace – All Applicable Models
Lubricate and check chassis. Change oil and oil filter. Check air filter and breather filter. Check all fluid levels and tire pressures. Perform 40 point courtesy inspection. If applicable.
DEARMUS H. gave our service a 5 star review on 12/26/2019
LEFT FRONT RIGHT FRONT PADS ____4MM____ PADS ____3MM____ ROTOR ____1.100____ ROTOR ____1.096____ DISCARD ____1.024____ LEFT REAR RIGHT REAR [ ]PAD [ ]PAD [ ]SHOE ____4MM____ [ ]SHOE ____4MM____ LEFT REAR RIGHT REAR [ ]ROTOR [ ]ROTOR [ ]DRUM ____.620____ [ ]DRUM ____.621____ DISCARD ____.551____ BRAKE FLUID ___OK____
Lubricate and check chassis. Change oil and oil filter. Check air filter and breather filter. Check all fluid levels and tire pressures. Perform 40 point courtesy inspection. If applicable.
Replace rear brake linings. Inspect condition and thickness of rear brake disc rotors. Retract rear brake caliper actuators. Clean and lubricate rear brake caliper slide mechanism. Road test vehicle.
Replace front brake pad linings. Clean and lubricate brake calipers and slide mechanisms. Check and fill brake fluid. Bleed air from system. Road test vehicle.
MOUNT AND BALANCE 2 TIRES
STATE FEE
DISP FEE
ROAD TEST VEHICLE. INSTALL ALIGNMENT EQUIPMENT. CHECK CASTER, CAMBER AND TOE SETTINGS. ADVISE OF ANY NEEDED ADJUSTMENTS TO CASTER OR CAMBER. IF CASTER AND/OR CAMBER ARE NOT WITHIN MANUFACTURER'S SPECIFICATIONS, PREPARE ESTIMATE TO INSTALL CORRECT ADJUSTMENT DEVICES. REMOVE ALIGNMENT EQUIPMENT. ROAD TEST.
JOHN L. gave our service a 5 star review on 7/4/2019